Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
See the difference
Before
After
Before
After
Before
AfterHow Much Does Chimney Liner & Rebuild Cost in Kent?
Chimney liner and rebuild work in Kent typically runs from about $600 for HeatShield flue resurfacing on a single flue up to $9,000 or more for a full masonry rebuild with a new liner. A standard stainless steel relining on a one-story home with a straight flue usually lands between $2,400 and $4,800, and most jobs include the inspection that tells you which of those you actually need. The written estimate sets the final price, and we give that estimate for free.
Chimney work in Kent is a different animal from what you’d price in a drier part of the state. The Puget Sound basin gets a long, wet heating season, and that damp air is hard on masonry. Freeze-thaw cycles along the East Hill ridge work at mortar joints and brick faces year after year. Fir, alder and maple smoke puts creosote and moisture on the flue interior season after season. By the time a homeowner notices a problem, there are often two or three issues to price, not one. That’s why a good cost estimate starts with an inspection, not a guess over the phone.
Chimney Liner & Rebuild Cost Breakdown (2026)
Here are the typical ranges for the work we see in Kent homes. Every flue is different, so treat these as starting points. The written estimate after inspection is the number that counts.
| Scope of work | Typical cost range | What’s included |
|---|---|---|
| Level 1 or 2 chimney inspection | $150 – $400 | Visual assessment, flue scan, written findings |
| HeatShield flue resurfacing (per flue) | $600 – $1,800 | Crack and joint repair on a liner that’s still structurally sound |
| Stainless steel relining, straight flue (per flue) | $2,400 – $4,800 | DuraFlex liner, insulation, cap, connections |
| Relining with offsets or a complex run | $4,800 – $7,500 | DuraFlex liner routed around bends and offsets, custom fit |
| Partial masonry rebuild (crown or top courses) | $1,800 – $4,500 | Tear-out and rebuild of damaged brick and mortar |
| Full chimney rebuild (above roofline) | $6,000 – $15,000+ | Full reconstruction with new liner, crown, and flashing |
| Chimney crown replacement | $600 – $1,600 | New poured or formed crown to shed water |
| Chimney cap (Gelco, Famco, Olympia) | $250 – $700 | Stainless or copper cap matched to the flue |
| Damper replacement | $400 – $1,200 | Top-seal damper for a tighter, more efficient flue |
What pushes a job toward the top of a range? Height and access matter more than people expect. A chimney on a steep-pitch roof, or one that sits high above the roofline, takes more time and setup than a short chimney on a low-slope roof. Offsets in the flue complicate a DuraFlex liner install because the liner has to be routed and fitted to the bend. And a rebuild that uncovers hidden damage to the firebox or smoke chamber adds scope once the crew is in there. What pulls a job down is catching it early. If HeatShield resurfacing can restore a lightly cracked flue, you avoid the full cost of relining entirely. That assessment, done before we recommend a full relining, is where we think homeowners get the most value out of the inspection.
What Affects Chimney Liner & Rebuild Pricing in Kent
The same relining job can price two very different ways across Kent, and it’s almost always one of these factors.
- Wet weather and moisture damage. Kent’s long rainy season is the single biggest driver of rebuild costs here. Water gets into masonry through a failing crown or capillary cracks, freezes, and spalls the brick face off. A chimney that’s been seeped into for several winters usually needs more rebuild work than a visual look first suggests.
- The type of flue you have. A clay tile liner with failed joints can often take HeatShield resurfacing at a fraction of relining cost. A flue with a collapsed tile or severe spalling can’t be resurfaced and needs a full DuraFlex relining. Knowing which you have starts with an inspection.
- How you use your chimney. A wood-burning fireplace used heavily through Kent’s winters builds creosote and internal moisture faster than a gas insert run a few hours a week. The fuel and the frequency both shape how much wear and how often the work comes due.
- Chimney height and roof access. A chimney two stories above the ridge takes longer to work safely than one at the eaves. The access setup and time on the roof carry through to the labor line.
- Offsets and complex flue runs. Older Kent homes sometimes have a flue that jogs around the framing. DuraFlex relining handles that, but it takes custom fitting and time, which runs the range higher than a straight vertical drop.
- Correct parts and fittings. A cap or damper matched to the exact flue configuration is not the same as a universal fit. Getting the Gelco, Famco or Olympia Chimney components right the first time avoids a callback and a warranty issue down the road.
How to Save on Chimney Liner & Rebuild
There’s no way to make a full relining cheap, but there are real ways to keep the number honest.
Catch the cracks early. The single biggest savings in chimney work is restoring a flue with HeatShield resurfacing while the liner is still structurally sound, instead of waiting until it fails and needs full relining. Resurfacing at $600 to $1,800 against relining at $2,400 to $4,800 is the biggest spread on the whole table.
Get an inspection before you commit. Ask what condition the flue is actually in, what the options are, and what each costs. A company that jumps straight to relining without checking whether resurfacing would work is skipping a step that can save you money.
Get it done before water gets in. A $600 to $1,600 crown replacement now, or a cap at $250 to $700, protects masonry that would otherwise need rebuild work at $6,000 and up. The fix up top is cheaper than the rebuild below.
Get more than one quote, and read what’s in it. Compare line items, not just the bottom number. A quote that leaves out insulation, the cap, or the connections isn’t the same job.
We give free estimates, and we show you what we find with photos and a plain explanation before anyone picks up a tool. Call (866) 942-7714 to set one up.
HeatShield Resurfacing vs. Full Relining: Which Do You Need?
If the flue liner is cracked or jointed but still structurally sound, HeatShield resurfacing restores it for roughly $600 to $1,800. If the liner is collapsed, badly spalled or missing, a full DuraFlex relining is the right fix at $2,400 to $4,800. The inspection tells you which.
HeatShield is a resurfacing system applied to the interior of the existing flue. It seals cracks and rebuilds the liner face without the demolition and cost of a full relining, which is why we’re HeatShield-qualified. Most sweep-only companies clean flues and hand you a relining quote because resurfacing is outside their scope. When a liner can still be restored, we tell you, and we show you the range for both options side by side.
Full relining with DuraFlex is the answer when the existing liner is beyond resurfacing. That’s a bigger job and a bigger cost, but it gives you a new stainless liner sized to the appliance, insulated and capped correctly. We work with DuraFlex systems specifically, so a complex run or an offset flue that other companies refer out is work we can take on directly.
What Does a Chimney Rebuild Involve in Kent?
A partial rebuild that replaces a damaged crown or the top courses of brick typically runs $1,800 to $4,500. A full rebuild above the roofline, with a new liner and crown, ranges from $6,000 to $15,000 or more. The scope and the extent of hidden damage set the number.
A rebuild isn’t just cosmetic repair. When water has gotten into masonry through a failed crown or bad flashing and then frozen through several winters, brick faces spall and mortar joints crumble. A rebuild pulls out the compromised material and replaces it with sound brick, fresh mortar and a new crown built to shed water off the top. We tie the rebuild to the liner and cap so the whole assembly is sealed against the weather. The wet Kent winters are exactly why the crown and cap detail matters so much here, and it’s the detail that gets skipped on a cheap rebuild.
One safety note on any of this work: a chimney liner and flue carry combustion gases and, in a wood-burning chimney, creosote. The liner has to be continuous, intact, and correctly sized for the appliance it serves, or gases can escape into the house. This isn’t a project for a homeowner with a ladder and a kit. The structural and safety judgment is why a trained professional does the inspection and sign-off before, and after, the work.
FAQs – Chimney Liner & Rebuild Cost
How much does chimney liner replacement cost in Kent?
Chimney liner replacement in Kent typically costs between $2,400 and $4,800 for a standard stainless steel relining on a one-story home with a straight flue, and $4,800 to $7,500 for a complex run with offsets. The range moves with height, access, and whether HeatShield resurfacing could have handled the liner instead. Call (866) 942-7714 for a free estimate on your flue.
Is it cheaper to resurface a flue or replace the liner?
Resurfacing is usually cheaper. HeatShield resurfacing runs $600 to $1,800 per flue, against $2,400 to $4,800 for a full relining. Resurfacing only works when the existing liner is still structurally sound, though, so the inspection tells you which option applies. Call (866) 942-7714 and we’ll show you both numbers before you decide.
How much does a chimney rebuild cost in Kent?
A partial rebuild of the crown or top courses runs $1,800 to $4,500, and a full rebuild above the roofline, with a new liner and crown, ranges from $6,000 to $15,000 or more. The wet Kent climate drives how much masonry water damage a rebuild has to correct. Call (866) 942-7714 for a free estimate on your chimney.
Can I get a free estimate for chimney liner or rebuild work?
Yes. We give free written estimates and show you what we find, with photos and a plain explanation, before any work starts. Call (866) 942-7714. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. The written estimate sets the price.
How long does chimney relining or rebuilding take?
Most relining jobs are completed in a single day, while a full masonry rebuild can take several days depending on scope and how much hidden damage turns up. HeatShield resurfacing is often the fastest of the options. Call (866) 942-7714 to get a timeline for your specific job.
How Chimney Sweep Kent Handles Liner and Rebuild Work
We’re a dedicated chimney specialist, not a generalist handyman with a brush. Sweeping, repair and inspection are three disciplines under one roof, and that means one company sees your chimney from the first call to the final sign-off. No hand-offs to a second contractor partway through the job, no gaps in who’s accountable for the work.
We specify professional-grade materials from suppliers the chimney industry relies on: DuraFlex for relining, HeatShield for flue resurfacing, and Gelco, Olympia Chimney, Famco and Copperfield for caps, dampers and venting components. Matching the right supplier to each flue configuration is how a cap and damper are specified correctly the first time and how a rebuild gets sealed against a wet Western Washington winter. Our technicians have up to experience, and we offer inspections as a standalone service supporting real estate transactions, insurance requirements and annual safety checks.
If you found us looking for a chimney sweep in Kent, start there. If you want the full picture of what we do across the area, our Kent page covers the sweep, repair and inspection scope together.
When to Call for Chimney Liner or Rebuild Pricing
Call (866) 942-7714 for a free estimate and we’ll tell you what your chimney needs before you spend a dollar on it. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. We show you what we find, lay out the options with real numbers, and you decide. Getting an inspection now instead of after a wet winter of water damage is the cheapest part of the whole process.
Pricing reflects the Kent market as of 2026. Chimney Sweep Kent offers free estimates – call (866) 942-7714.
Written by the team at Chimney Sweep Kent.
What Our Customers Say
"Drop cloths everywhere, HEPA vac, and not a speck of soot on the carpet. I'd been dreading the mess for nothing."
- Colleen Whitaker"Thorough sweep and a clear report. He was running late from the job before and arrived near the end of the window, though he did call to warn me."
- Heather Hoffman"Level two inspection before we bought the house. The report was detailed enough to use as a negotiating point and he explained every photo in it."
- Bryce Barrett